24 results, page 1 of 2.
-
Guide · Building systems
Fire alarm system inspections
A fire alarm system has to detect a fire, warn occupants and, in many buildings, call the fire department and operate other fire safety systems. Under the fire codes in force across Canada, owners must keep it working through routine checks and a full annual …
-
Service · Building systems
Fire inspections, verification and monitoring
Fire protection systems in Canadian buildings must be installed, verified, monitored and inspected to specific standards, and much of that work has to be done by qualified fire protection technicians. We give owners an independent view of their fire …
-
Guide · Building systems
Smoke and carbon monoxide alarms
Smoke alarms give people in a home or suite the early warning they need to get out of a fire. Carbon monoxide (CO) alarms warn of a gas that cannot be seen or smelled and can kill in a person's sleep. Both are required by building and fire codes in most homes …
-
Guide · Building systems
How fire alarm monitoring works
Fire alarm monitoring connects a building's fire alarm system to a signal receiving centre that is staffed around the clock. When the system detects a fire, the centre calls the fire department, even if nobody is in the building. It also watches for trouble …
-
Guide · Building systems
Fire extinguisher inspections
Portable fire extinguishers are the first line of defence against small fires, but only if they are the right type, in the right place, charged and ready. Owners are responsible for regular visual inspections, usually monthly, and for having qualified …
-
Guide · Building systems
Fire alarm verification explained
A fire alarm verification is a complete inspection and test of a new or altered fire alarm system, done to CAN/ULC-S537 before the system is relied on. It confirms that the system was installed as designed, that every device works and that it meets the …
-
Guide · Building systems
Boiler inspection basics
… pressure vessel program. Owners are responsible for keeping them in safe condition between those inspections, which means routine checks, competent operators where required, licensed service and good records. Who regulates boilers Each province has its own …
-
Guide · Building systems
How a fire investigation works
A fire investigation works out where a fire started and what caused it, using a structured, scientific method. Several parties may investigate the same fire for different reasons: the fire service, police, insurers and engineers acting for owners or other …
-
Service · Building systems
Fire investigations
After a fire, owners need to know what happened to the building's systems, what can be saved and what has to be replaced. We provide engineering input on mechanical, electrical and life safety systems after a fire, working alongside the fire service, insurers …
-
Guide · Building systems
Sprinkler system inspections
Sprinkler systems control or put out fires automatically, but only if water can reach the heads and the heads are free to work. Inspection, testing and maintenance on a set schedule keeps valves open, gauges normal, heads clear and pipes free of corrosion and …
-
Service · Building systems
Diesel generator inspections
A diesel generator inspection tells you whether your standby power will start, transfer and carry the load when the utility fails. We inspect the engine, generator, fuel system, transfer equipment and records, and give you a clear list of what needs …
-
Guide · Building systems
Emergency lighting and exit sign testing
… they sit unused most of the time, batteries die and lamps fail without anyone noticing. Regular inspection and testing, done and recorded on the schedule your provincial fire code sets, is how owners make sure they work when they are needed. How emergency …
-
Guide · Building systems
Compressed air system safety
… to contribute to hearing loss. See our guide on noise and hearing conservation. Heat, oil and fire Compressors run hot. Oil carryover, oily rags and poor ventilation in the compressor room add fire risk. Lubricated compressors that overheat can, in rare …
-
Guide · Building systems
Standby generator maintenance
… sitting still, and then it has to start and carry the load the moment the utility fails. Regular inspection, exercise under load and planned service are what make that possible. A generator that is only looked at when the power goes out is the one most likely …
-
Guide · Building systems
A furnace maintenance checklist
… importantly, vents combustion gases safely outside. The checklist below applies to typical gas-fired forced-air furnaces. Always follow the manufacturer's instructions for your equipment. It helps to picture what is going on inside the cabinet. Two streams of …
-
Guide · Building systems
Commissioning a new building
… many trades, each focused on their own scope. Mechanical, electrical, controls, plumbing and fire protection systems all have to work together, and the gaps between contracts are where problems hide. Typical results of skipping commissioning include equipment …
-
Guide · Building systems
Switchgear and panel maintenance
… keeps protective devices working as designed and finds problems before they become outages or fires. Why maintenance matters Distribution equipment has two jobs: carry current every day, and interrupt it safely when there is a fault. The first job can be …
-
Guide · Building systems
Building automation systems
… electrical systems: it starts and stops equipment, holds temperatures and pressures, and raises alarms. When it is set up and maintained well, it saves energy and keeps occupants comfortable. When it drifts, it can quietly waste a great deal of both. What a …
-
Guide · Building systems
Automatic transfer switches
… loads Larger buildings often have more than one ATS. Life safety loads such as emergency lighting, fire alarm and fire pumps may be on separate transfer switches from loads like elevators, heating or business equipment, and the electrical code requires …
-
Guide · Building systems
Generator load bank testing
… specified load, and allows a load bank to be used where the building load is too low. The National Fire Code of Canada and provincial fire codes reference these requirements. Check the current edition and what your province and local fire authority require, …
Not finding it? Ask us or call 1-833-888-0091.